Rm-materials-handling WIRE ROPE HOISTS Service Manual de usuario Pagina 108
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
R&M Materials Handling, Inc.
4501 Gateway Boulevard
Springfield, Ohio 45502
P.: (937) 328-5100
FAX: (937) 325-5319
108/130
R&M Materials Handling, Inc. reserves the right to alter or amend the above information without notice.
! Tighten the lowest fixing screws (2) for the fixing brackets of the trolley on both sides to the
correct tightening torque. Refer to the section “Recommended tightening torques”.
• Tighten the locking screws (1) for trolley adjustment on both sides.
Drum size φ 355/406mm and φ 303 for low profile
c_r2bmla1c
1. Adjusting bar
2. Locking screws
3. Frame tube
4. Locking screw
• Remove the temporary transport supports. Take the hoist out of the packing and move it to the
installation site. Lift the hoist using slings around the frame tube.
• Loosen the locking (2) of adjusting bar (1). Adjust the distance between the travel wheels (A) so that it
is slightly wider than the beam flange (B) for installation purposes.
! Do not loosen the fixing parts on the drum-side of the trolley
• Lift the hoist onto the beam. Adjust the X measurement until there is a gap of approximately 3…5mm
between the flange of the travel wheels and the flange of the beam. Use a nylon mallet to adjust the X
measurement.
• Check the wheels of the trolley are correctly aligned.
! Tighten the locking screw (2) and (4) of the adjusting bar on both sides to the correct
tightening torque. Refer to the section “Recommended tightening torques”.
6.3.1 Outfitting the hoist
• Install the power supply. Refer to the section “Connecting the to mains network”.
• Adjust the limit switch for hoisting. Refer to the section “Adjusting hoisting limit switch”.
• Carry out the commissioning inspection and complete the commissioning log. Refer to the section
“Commissioning”.
- SERVICE MANUAL FOR HOIST 1
- # Caution 7
- 3 Safe operation 8
- 3.4 Safe working principles 9
- 4 Hoist manufacturer 13
- 4.3.1 Spare parts 14
- 5.4 Fixed Hoist 21
- 5.5 Machinery Hoist 24
- 5.6 Trolley buffers 25
- 5.6.1 Service 25
- 5.7 Hoisting machinery 25
- 5.7.1 Service 25
- 5.7.2 Assembly 25
- 5.8 Hoisting gearbox 30
- 5.8.1 Service 31
- 5.8.2 Assembly 31
- 5.9.1 Service 32
- 5.9.1.1 Hoisting motor 32
- 5.9.1.2 Brake 33
- 5.10 Second brake 34
- 5.12 Manual crank 36
- 5.12.4 Assembly 37
- 5.13.1 Service 38
- 5.14.1 Service 39
- 5.14.2 Assembly 40
- 5.14.3 Adjustment 41
- 5.14.4 Fine adjustment 42
- 5.15.1 Service 43
- 5.15.2 Assembly 44
- 5.15.3 Adjustment 45
- 5.18.1 Service 49
- 5.19 Travelling machinery 50
- 5.19.1 Service 52
- 5.19.1.1 Traveling motor 52
- 5.19.1.2 Traveling gearbox 52
- 5.19.1.3 Traveling brake 52
- 2 178 6 5 4 3 53
- 10 11 12 53
- 5.22 Inverter for travel 56
- 5.23 Rope drum 58
- 5.23.3 Drum wear inspection 59
- 5.24 Rope guide 61
- -> 10.2004 67
- 5.25 Rope clamps 68
- 5.25.1 Service 68
- 5.26 Drum Brake 68
- 5.26.1 Holding Brake 69
- 5.26.2 Service 69
- Overspeed Brake 70
- 5.26.5 Service 71
- 5.28 Rope anchorage 76
- 5.28.1 Service 77
- 5.28.2 Assembly 78
- 5.29.1 Service 87
- 5.29.2 Hook block assembly 88
- 5.30 Wire rope 94
- 5.30.1 Wire rope structure 94
- 5.30.2 Service 95
- 5.30.2.2 Discard criterias 95
- 5.30.3 Assembly 98
- 5.31 Overload protection 99
- 5.31.1 Service 100
- 5.32.1 Service 102
- 5.33 Load signal amplifier 103
- 5.33.1 Adjustment 103
- 6 Installation 105
- 6.3 Low headroom trolley 107
- 6.3.1 Outfitting the hoist 108
- 6.4.1 Outfitting the hoist 109
- 6.4 Double-girder trolley 109
- 6.5 Normal headroom trolley 110
- 6.5.1 Straight beam 110
- 0,1-0,2 mm 111
- 6.5.3 Outfitting the hoist 112
- 6.6.1 Straight beam 113
- 6.6.2 Curved beam 115
- 6.6.3 Outfitting the hoist 116
- 6.7.1 Outfitting the hoist 117
- 6.8.1 Outfitting the hoist 117
- 7 Commissioning 119
- 8 Maintenance 122
- 8.4 General Overhaul, GO 126
- 9 Lubricants 128
- 9.2 Lubricant quantities 129
- 10 Troubleshooting 130
Relacionado con productos y manuales para Izar Rm-materials-handling WIRE ROPE HOISTS Service
Izar Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist General Manual de usuario
(42 paginas)
(42 paginas)
Izar Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 Manual de usuario
(85 paginas)
(85 paginas)
Izar Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 5 Manual de usuario
(89 paginas)
(89 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales